Beiträge von silent storm

Okay, after research, I found that error 05 on litle display is related to pressure switch lubrication headstock and gearbox. Dunno if it's the pump or sensor for presure but I jumped the sensor and everything is fully working. Tomorrow I'll check pump and sensor and get replaced what ever is bad.

Lets move on the next

error I35 and 05 on i guess its called PLC errors on litle display back next to main switch.
it comes 1 time a day, and it was easy to get it off buy open/close door and playing with key on keyboard. Now it wont turn off, its there and cant zero axes, cant do nothing exept moving axes with hand mode or turn spindle with button on keyboard (10rpm)
I looked at the switch on door its okay and I can hear when i press it some relay in cabin clicking

Oil levels are okay

Dont know what to do O.o

Zitat von Mahoist

Hello,

these are the parameters for the changing positions:

Greetings

From Maho

Pickup-Wechsler
		Tool location 1
MC	1100	Change position X
MC	1101	Change position Z
MC	1103	Change position Y
		Tool station 2
MC	1105	Change position X
MC	1106	Change position Z
MC	1108	Change position Y
		Tool station 3
MC	1110	Change position X
MC	1111	Change position Z
MC	1113	Change position Y
		Tool station 4
MC	1115	Change position X
MC	1116	Change position Z
MC	1118	Change position Y
		Tool location 5
MC	1120	Change position X
MC	1121	Change position Z
MC	1123	Change position Y
		Tool slot 6
MC	1125	Change position X
MC	1126	Change position Z
MC	1128	Change position Y
		Tool slot 7
MC	1130	Change position X
MC	1131	Change position Z
MC	1133	Change position Y
		Tool slot 8
MC	1135	Change position X
MC	1136	Change position Z
MC	1138	Change position Y
		Tool slot 9
MC	1140	Change position X
MC	1141	Change position Z
MC	1143	Change position Y
		Tool slot 10
MC	1145	Change position X
MC	1146	Change position Z
MC	1148	Change position Y

THANKS MAHOIST!

Guys thanks for help, I managed to get it working. It was like MarcoPry sad. The M19 position must be set. I did it by rotatiting encoder on gearbox.

Now the m6 is working BUT. Always there is but, the Y axis is going about 5mm higher than it should and spindle is dropping tools on more than 20 procents of feed rate. It leaves tool and go to another but clamping is slow it don't have time to clamp tool but she is on her way out. Is there any screw or smth to accumulation of the spring that grips tool? And is there parameter to set the hight of Y axis

Zitat von Mahoist

Hello,

Input 21 is missing, Terminal 367 (+ 24V).

367 need 24V?

Greetings

From Maho

Alles anzeigen

Im not sure that I understand you... there is no Terminal 367 on this board or im missing smthg

Zitat von Mahoist

Hello,
does it mean this wire is connected to the Output ribbon cable ?

pasted-from-clipboard.png

I think the switch is 21S3.

It looks that the quill is on top.

Greetings

From Maho

Alles anzeigen

Yeah it look like it's connected to a ribbon cable but it's not, it's just there not connected to anything.

Zitat von MarcoPry

Please check that the spindle is positioned correctly. (M19)

Select M19

How is the spindle positioned? Parallel to X, to Y or at an angle.

It is not at the good side. It need to turn a litle less than half a turn

To add, there are 2 sensors. Picture below

Here are some pictures.

Edited pictures with arrows, thus wire is not connected and goes from the relay or what ever it is.

And there is a video

Okay, thanks. Picture below

So this is it, the upper sensor witch is "on" I suppose its for pinole (for atc pinole must be full up) because if i move pinole a litle down the sensor goes "off"

Lower sensor it should be for M19 i guess? is "off" Im not sure how to check is it working or not. When i hit M19 spindle turn around and stop where is now (on picture). I think sensor is working but can see the led light, cuz it isnt working spindle would not stop? Now I dont know how to rotate spindle in right direction and save that spot. My thinking is that is should change some constants?

It if I get close to sensor with srewdriver to simulate lower sensor dont get led to turn on. this works on upper one

T0 M66 give me T0 on screen and turn ON the spindle O.o

T0 M67 also

New one, after stopping spindle, i give a try to T2M6 and it worked but spindle is not oriented good and i get error I 158 -tool clamping vertical released 0-signal

okay, i managed this to work but now im stuck with error P114-tool in spindle not from magazine..

Hey there.
Im new owner of maho 700c with philiops 432, 1988 yr of production.

the machine is equiped with atc in front of table, dunno how it calls. see the picture. Anyway, i cant get it to work, 1st idont know what type of toolchanger is for connst, 1-6? Dont have any book to read from.

It was on 5 in the cdonst menu, but previous owner didnt use it and he used to change tools with m66,m67 but i want it get to work
if anyone have this type of tooolchanger please let me know or know how it suposed to work

.

This type of toolchanger is